Request Information
Gas Detection for Life

Gas detection should not be complicated. The Beacon™ 110 is gas detection simplified.

The Beacon™ 110 is a powerful, low cost fixed system controller for one point of gas detection. It is microprocessor controlled, simple to install and operate, and priced to be the industry’s best value single gas detection controller. It is capable of accepting RKI sensors directly for LEL level combustibles, oxygen, CO2, and toxic gas sensors.
Unit of Measure

Brands

 N/A Beacon™ RKI Instruments

Approvals

 N/A Canadian Standards Association (CSA) Certified to CSA C22.2 No. 61010-1-04 and Underwriters' Laboratories (UL) 61010-1

Material Warranty

 N/A 1 year

Workmanship Warranty

 N/A 1 year

Industry Standards/Certifications

 N/A CCSAUS

Package Type

 N/A Each

Units Per Package

 N/A 1

Height

 N/A 8.5 in216 mm

Depth

 N/A 7.0 in178 mm

Width

 N/A 4.3 in109 mm

Enclosure

 N/A Wall Mounting Gray Fiberglass with Hinged Cover

Conduit Connection

 N/A 3/4" NPT Conduit Hubs, 2 Provided. 1 for Sensor Wiring and 1 for Power and Relay Wiring.

Wiring Termination

 N/A Screw Type Terminal Block, 14 Gauge Maximum

Controls

 N/A 3 Internal Push Buttons for Setup, Programming, and Calibration. 1 External push button for alarm reset.

Universal Alternating Current (AC) Voltage

 N/A 115 V220 V

Nominal Direct Current (DC) Voltage

 N/A 24 V

Note for Power

 N/A Battery Backup Option Available

Operating Temperature

 N/A -20 to 50 ºC-4 to 122 ºF

Storage Temperature

 N/A -20 to 70 ºC-4 to 158 ºF

Enclosure Rating

 N/A NEMA-4X Enclosure, Chemical, and Weather Resistant. Suitable for Indoor and Outdoor Installations.

Direct Wired Sensors

 N/A LEL, Oxygen, Carbon Dioxide, and Toxic Gas Sensors. Amplifier not Required for Less Than 500 Feet

4 to 20 Milliampere (mA) Sensors

 N/A Accepts any 4 to 20 mA transmitter (24 VDC, 2 or 3 wire). A wide variety of RKI/Riken sensors are available with 4 to 20 mA signals. Wiring distances up to 8,000 feet

Sampling Methods

 N/A Diffusion and Sample Draw Heads Available.

Relays

 N/A Three relays - 10 amp rating (at 115 VAC), SPDT isolated contacts. 2 relays for gas alarms and 1 trouble relay. Relays fully programmable for: increasing or decreasing alarm, latching or self reset, normally energized or normally de-energized, time delay

4 to 20 Milliampere (mA) Output

 N/A Signal Output, 4 to 20 mA (Maximum Load Impedance 500 ohms), per Channel.

24 Direct Current (DC) Voltage Output

 N/A 24 VDC (400 mA max) Output Provided to Operate Sample Drawing Adapters or Other Accessories.

Display

 N/A 2 x 8 Alphanumeric Display with Backlighting

Audible

 N/A Built-in Audible Alarm, 94 dB, Mounted on Enclosure Coded Output: Pulsing = Gas Alarm, Steady = Fail

Visual

 N/A 3 Light Emitting Diode (LED) on the Front Cover for Alarm Status Indication, and Malfunction. Optional Top-mount Strobe.

N/A

  • Low cost versatile solution
  • Compact, weatherproof, NEMA 4X enclosure
  • Long life sensors (2+ years typical)
  • Accepts RKI LEL/O2/CO2/toxic direct connect sensors
  • Accepts any 4 to 20 mA transmitter
  • Audible alarm with reset button
  • Two programmable alarm levels
  • Built-in trouble alarm with relay
  • Relay rating 10 amps, form C
  • Provides 4 to 20 mA output
  • Optional Strobe

N/A

  • Petrochemical plants
  • Refineries
  • Water and wastewater treatment plants
  • Pulp and paper mills
  • Gas, telephone, and electric utilities
  • Parking garages
  • Manufacturing facilities
  • Steel
  • Automotive
  • HVAC

N/A The Beacon™ 110 can also accept any 4 to 20 mA transmitter (2 or 3 wire, 24 VDC). Sensors can be mounted directly at the Beacon™ 110 housing, or can be wired remote from the controller.

The 10 amp rated relay contacts allow direct control of external alarms and horns. The digital display has backlighting and simultaneous readout of the gas type and concentration.

The Beacon™ 110 is also housed in a NEMA 4X rated case for a weather tight seal. This case design complies with lock out / tag out standards and can be fully secured. An external reset switch allows the alarm to be silenced from outside of the controller housing. The Beacon™ 110 ships complete with a wall mounting kit for easy installation.

RKI offers the industry's widest selection of standard and toxic gas detection sensors, all of which can be utilized with the Beacon™ 110, providing gas monitoring protection for almost any application.

N/A Specifications subject to change without notice.

Made in the USA.